Coastal Shaft Collars - 1.125" Bore Diameter - Clamping Two Piece Shaft Collar - 303 Stainless Steel (1 Pack)

4.4 4.4 out of 5 stars | 243 ratings

Price: 12.75

Last update: 09-04-2024


About this item

These two-piece stainless steel split shaft collars have an inside diameter of 1.125 inches, an outside diameter of 1.875 inches and a thickness of 0.5 inches. This pack includes 1 split collar and its corresponding screws.
Made in the USA by Coastal Machine Works. We strive to deliver high quality and precise collars. Every collar has its edges and holes deburred and its corresponding inside diameter bore engraved on its front face for easy identification.
Made from 303 stainless steel, these shaft collars have excellent corrosion resistance and are ideal for wet environments or when corrosive chemicals are present.
The two-piece design makes installation simple. The split collar can be disassembled and reassembled anywhere along the shaft without needing to remove other components or having access to the ends of the shaft.
Strong, even clamping pressure around the shaft is created using the two included 1/4-28 x 5/8” stainless steel socket head screws. Compared to set screw style collars, the two-piece design has significantly higher clamping force and will not mar the shaft/pipe.

From the brand

Previous page
Next page

Top reviews from the United States

Doug
5.0 out of 5 stars Excellent Construction, Excellent Finish, Holds Tight
Reviewed in the United States on August 11, 2024
I used this as a counterweight stop for my telescope counterweights. The weights are around 50 lbs and need to be held tightly in place on a delicate instrument. When they arrived the finish was clean and bright, with no rough edges, and no excess gum or oil. The bolts fit smoothly and tightly, and the collar held the weights tightly in place with no motion. I also tried a competitor, but the fit and finish on these were the best. After seeing both side-by-side, I purchased several more of these.
Customer image
Doug
5.0 out of 5 stars Excellent Construction, Excellent Finish, Holds Tight
Reviewed in the United States on August 11, 2024
I used this as a counterweight stop for my telescope counterweights. The weights are around 50 lbs and need to be held tightly in place on a delicate instrument. When they arrived the finish was clean and bright, with no rough edges, and no excess gum or oil. The bolts fit smoothly and tightly, and the collar held the weights tightly in place with no motion. I also tried a competitor, but the fit and finish on these were the best. After seeing both side-by-side, I purchased several more of these.
Images in this review
Customer image
Steven Morano
5.0 out of 5 stars Ridiculously nice collar
Reviewed in the United States on August 17, 2024
This is an absolute piece of jewelry. Beautiful machining, high quality materials, made in the USA- what's not to like? They are also similarly priced to non-American made alternatives. I used them in place of push nuts to hold new wheels onto my pressure washer. One review mentions that the collar isn't round when fully closed- this is intentional, as if it was, it wouldn't grab the shaft. If you need a shaft collar for anything, these are an obscenely good value. Buy with confidence.
Triple Bogie
5.0 out of 5 stars The stainless steel quality used for the stop collar is excellent but costly.
Reviewed in the United States on June 14, 2024
I am using this as a bowling ball drill bit stopper collar ring for Jo Po thumb inserts. I am using the 1” inside diameter stainless steel stop ring collar with a Jayhawk brand 1 1/2” bowling ball drill bit. The top part of the 1 1/2” drill bit is 1”. This 1” stop collar ring fits perfectly and uses a 6 point hex 3/16” bit to tighten or loosen the bolt. If you only have a hex set in mm units, you will not be able to tighten the bolts. I just so happens to have the 3/16” bit in a set that came with both mm and inch format multiple bits. The quality of the stainless steel is excellent. The screw in bolts work as should and make sure to screw in both evenly as this stop ring is made to leave a gap after fully tighten on. 1 inch diameter bit. I would suggest that the company leave a choice to the Amazon customer to choose between mm and inch format for the bolts. i feel this is the best out there in USA made quality. I used a digital caliper to measure 3.22” to the stop of the stop ring before tightening down the bolts. This is Jo Po recommended drilling depth for their outer sleeve ring. Make sure the drill press is precisely set at zero / zero using the thumb slug contoured cutting bit to calibrate the settings. Value for the money is on the higher side but at a few bucks more, I just bit the bullet so I didn’t have to worry about which ones to get. I rate this stainless steel 1” stop collar ring at 5 STARS and will update again later of needed.
Adi Dassler
5.0 out of 5 stars Great product
Reviewed in the United States on August 7, 2024
Well made and perfect fit.
Jon R
5.0 out of 5 stars Quality product
Reviewed in the United States on July 24, 2024
Very high quality, excellent price, sizing was perfect
JeepingBrad
4.0 out of 5 stars Very nice and good quality but not quite "round"
Reviewed in the United States on October 4, 2023
Very nice and good quality but they are not exactly round when fully clamped together, as I needed (see pics). A bit of an oval shape but they do work and am satisfied with the quality.
Customer image
JeepingBrad
4.0 out of 5 stars Very nice and good quality but not quite "round"
Reviewed in the United States on October 4, 2023
Very nice and good quality but they are not exactly round when fully clamped together, as I needed (see pics). A bit of an oval shape but they do work and am satisfied with the quality.
Images in this review
Customer image Customer image
Alter Ego
3.0 out of 5 stars Smaller than Described, Had to Return as a Result!
Reviewed in the United States on May 2, 2023
I have an older donut shaped weight that was no longer available, in 33mm ID and 39mm ID of similar pricing. The 33 fit perfect but the 39 was too big. I sometimes use the 33 to hold the 39 on which gives a nice weight but I was looking for something closer in size to the 33mm weight. I decided on the 1-3/8" bore as that would be ever so slightly larger. My donut shaped weight was 15mm thick, so two additional at 12mm would fit nicely with 3 weights.

I want to start this off in saying that the actual product is nice quality, seems to be polished but does have a slight metallic smell but since it isn't 316L Surgical Stainless that is to be expected. The edges were de-burred but having a square shape leads to sharp corners, especially when trying to install it. My other weight has a fixed pin with a simple allen wrench head that's a different size.

I measured the ID of my current weight and it was 33.1mm which is 1.303 decimal inch. This purchased collar has an oval rather than round bore. The last time I checked a bore is a circle. Using my digital micrometer I measured my current ring and it was perfectly round at 33.1mm. The 1-3/8" bore(1.375mm decimal inch) measured as follows(pictured):
top to bottom with bolts horizontal to surface: 1.18 decimal inch or 30mm
left to right with bolts horizontal to surface: 1.33 decimal inch or 33.8mm

Ordering these in 1.375 or 1-3/8 bore, one would expect them to be a larger ID than 33mm which would be 1.29921 decimal inch. However being oval or flattened slightly makes the overall ID smaller as well as the fact that the widest point was 1.143mm smaller than the described bore size of 1.375 decimal inches which is 34.925mm.

Here are those measurements all together for sizing from smallest to largest:
1.180in = 30.0mm (This item Top to Bottom)
1.303in = 33.1mm (My previously purchased donut ring at 33mm ID)
1.330in = 33.8mm (This item Left to Right)
1.375in = 34.925mm (This items size as Described)
1.143mm (This item was this much smaller than indicated just over 1/16th of an inch nearly 3/32)

For my purpose, I needed it to be exact and I had to return for this reason, I am deducting 2 ⭐'because the product was not as described but the overall quality was decent. If using for intended purpose, skin will impress and 1/16th likely won't matter much.
Customer image
Alter Ego
3.0 out of 5 stars Smaller than Described, Had to Return as a Result!
Reviewed in the United States on May 2, 2023
I have an older donut shaped weight that was no longer available, in 33mm ID and 39mm ID of similar pricing. The 33 fit perfect but the 39 was too big. I sometimes use the 33 to hold the 39 on which gives a nice weight but I was looking for something closer in size to the 33mm weight. I decided on the 1-3/8" bore as that would be ever so slightly larger. My donut shaped weight was 15mm thick, so two additional at 12mm would fit nicely with 3 weights.

I want to start this off in saying that the actual product is nice quality, seems to be polished but does have a slight metallic smell but since it isn't 316L Surgical Stainless that is to be expected. The edges were de-burred but having a square shape leads to sharp corners, especially when trying to install it. My other weight has a fixed pin with a simple allen wrench head that's a different size.

I measured the ID of my current weight and it was 33.1mm which is 1.303 decimal inch. This purchased collar has an oval rather than round bore. The last time I checked a bore is a circle. Using my digital micrometer I measured my current ring and it was perfectly round at 33.1mm. The 1-3/8" bore(1.375mm decimal inch) measured as follows(pictured):
top to bottom with bolts horizontal to surface: 1.18 decimal inch or 30mm
left to right with bolts horizontal to surface: 1.33 decimal inch or 33.8mm

Ordering these in 1.375 or 1-3/8 bore, one would expect them to be a larger ID than 33mm which would be 1.29921 decimal inch. However being oval or flattened slightly makes the overall ID smaller as well as the fact that the widest point was 1.143mm smaller than the described bore size of 1.375 decimal inches which is 34.925mm.

Here are those measurements all together for sizing from smallest to largest:
1.180in = 30.0mm (This item Top to Bottom)
1.303in = 33.1mm (My previously purchased donut ring at 33mm ID)
1.330in = 33.8mm (This item Left to Right)
1.375in = 34.925mm (This items size as Described)
1.143mm (This item was this much smaller than indicated just over 1/16th of an inch nearly 3/32)

For my purpose, I needed it to be exact and I had to return for this reason, I am deducting 2 ⭐'because the product was not as described but the overall quality was decent. If using for intended purpose, skin will impress and 1/16th likely won't matter much.
Images in this review
Customer image Customer image Customer image
CMYK Josh
5.0 out of 5 stars Great for improvising
Reviewed in the United States on April 1, 2023
I needed rifle weights in a hurry. I found these and - surprise - they worked very well. I really needed 15mm bore but 0.625" with a mylar backer made these fit snug and not flatten the aluminum threads on the rifle's butt plate carrier. For anyone else who may want to try this, each 0.625" bore collar with screws weights precisely 50 grams. 4 weights in an order gets you 200 grams of weight. As for the collars, themselves, the machining was pristine. On a rifle where everything is stamped "Made In Germany", I really enjoy the irony of having "USA" prominently displayed. I've seen some people complaining about the gap; if it weren't for that gap, these wouldn't have clamped down to 15mm and they wouldn't have worked for me. Nice product.
Customer image
CMYK Josh
5.0 out of 5 stars Great for improvising
Reviewed in the United States on April 1, 2023
I needed rifle weights in a hurry. I found these and - surprise - they worked very well. I really needed 15mm bore but 0.625" with a mylar backer made these fit snug and not flatten the aluminum threads on the rifle's butt plate carrier. For anyone else who may want to try this, each 0.625" bore collar with screws weights precisely 50 grams. 4 weights in an order gets you 200 grams of weight. As for the collars, themselves, the machining was pristine. On a rifle where everything is stamped "Made In Germany", I really enjoy the irony of having "USA" prominently displayed. I've seen some people complaining about the gap; if it weren't for that gap, these wouldn't have clamped down to 15mm and they wouldn't have worked for me. Nice product.
Images in this review
Customer image

Best Sellers in

 
 

BESTORQ B42 or 5L450 Rubber V-Belt, Wrapped, Black, 45" Length x 0.66" Width x 0.44" Height

4.3 4.3 out of 5 stars 223
11.75
 
 

2 PCS 5 x 300mm (0.197 x 11.81 inches) Vigorous Linear Motion Rod, Case Hardened Chrome Shaft Linear Rail Rod Shaft for 3D Pr

4.5 4.5 out of 5 stars 87
9.69
 
 

26 inch Gas Shocks Struts 280343 654150 124Lb/552N Gas Spring Lift Supports for Camper Domestic Trailer Awning RV Bed Tonneau

4.5 4.5 out of 5 stars 990
36.99
 
 

RHKING #40 Roller Chain Sprocket B Type 5/8" Bore Rust Prevention Hardened 12 Tooth

4.4 4.4 out of 5 stars 125
18.5
 
 

BESTORQ B54 or 5L570 Rubber V-Belt, Wrapped, Black, 57" Length x 0.66" Width x 0.44" Height

4.3 4.3 out of 5 stars 245
14.95
 
 

R188 Open Deep Groove Ball Bearing, 1/4"mmx1/2"mmx3/16"mm Fidget Spinner Bearing with Nylon Caged (10 PCS)

4.7 4.7 out of 5 stars 51
11.99
 
 

4Pcs UCP204-12 Pillow Block Bearing 3/4 inch Bore Mounted Pillow Block Bearings Chrome Steel Bearings with 3/4" Bore, Self Al

4.5 4.5 out of 5 stars 1301
22.74
 
 

Goodyear 4LK460 Lawn and Garden Aramid V-Belt 1/2 x 46 in

4.3 4.3 out of 5 stars 69
20.29